A couple of minor potential bugs

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   So far I love the IFD-540 but after about 50 hours behind it I've noticed a couple of small but annoying issues. My installation has the current 10.0.3 software, an Aspen PFD, and a Shadin Miniflo-L fuel computer.

(1) The air data calculator defaults to an altitude in the flight levels (I think it's 27,200 feet but I wouldn't bet on that, I just know it's much higher than my service ceiling), shown in green text.  The Pilot Guide says "data fields in the various IFD calculators will be populated automatically with sensor data in green if it is available."  I'm not sure where the value is originating, but it is clearly wrong.  Maybe we can use GPS altitude here in a future software release?

(2) Based on what the Shadin is telling me for fuel reserve at destination, the 540 is incorrectly reporting the next waypoint as the destination in the GPS serial data.  This worked correctly before when I had my KLN-94 GPS installed. The fuel information on the IFD-540 itself is accurate (correctly shows fuel remaining at destination).

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Royski Members Profile Send Private Message Find Members Posts Add to Buddy List Groupie Joined: 26 Feb 2013 Status: Offline Points: 87	Post Options Post Reply Quote Royski Report Post Thanks(0) Quote Reply Topic: A couple of minor potential bugs Posted: 27 May 2015 at 11:26am
	So far I love the IFD-540 but after about 50 hours behind it I've noticed a couple of small but annoying issues. My installation has the current 10.0.3 software, an Aspen PFD, and a Shadin Miniflo-L fuel computer. (1) The air data calculator defaults to an altitude in the flight levels (I think it's 27,200 feet but I wouldn't bet on that, I just know it's much higher than my service ceiling), shown in green text. The Pilot Guide says "data fields in the various IFD calculators will be populated automatically with sensor data in green if it is available." I'm not sure where the value is originating, but it is clearly wrong. Maybe we can use GPS altitude here in a future software release? (2) Based on what the Shadin is telling me for fuel reserve at destination, the 540 is incorrectly reporting the next waypoint as the destination in the GPS serial data. This worked correctly before when I had my KLN-94 GPS installed. The fuel information on the IFD-540 itself is accurate (correctly shows fuel remaining at destination).

roltman Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 04 Aug 2011 Status: Offline Points: 173	Post Options Post Reply Quote roltman Report Post Thanks(0) Quote Reply Posted: 27 May 2015 at 12:30pm
	While I don't have the Aspen PFD, I do have the Miniflo-L and I have not seen what you are reporting on #2 after making several trips up/down the east coast via airways the intermediate waypoints and the destination have been reported correctly on both units. Maybe this will help narrow down your issue.

pburger Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 26 Dec 2013 Location: United States Status: Offline Points: 406	Post Options Post Reply Quote pburger Report Post Thanks(0) Quote Reply Posted: 27 May 2015 at 12:33pm
	On point (1), mine populates with the pressure altitude which is coming serially from my encoder.

jhbehrens Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 15 Dec 2012 Location: Netherlands Status: Offline Points: 128	Post Options Post Reply Quote jhbehrens Report Post Thanks(0) Quote Reply Posted: 28 May 2015 at 2:41am
	On point (2) check the install manual as there are settings in the IFD's setup screens for sending either the next waypoint or the destination to your totalizer. Edited by jhbehrens - 28 May 2015 at 2:41am