Avidyne Homepage
Forum Home Forum Home > Avidyne General > AXP340/322 ADS-B Transponder
  New Posts New Posts RSS Feed - AXP322 power on/off & config/maint mode
  FAQ FAQ  Forum Search   Register Register  Login Login

AXP322 power on/off & config/maint mode

 Post Reply Post Reply
Author
Message
chflyer View Drop Down
Senior Member
Senior Member
Avatar

Joined: 24 Jan 2013
Location: LSZK
Status: Offline
Points: 1035
Post Options Post Options   Thanks (0) Thanks(0)   Quote chflyer Quote  Post ReplyReply Direct Link To This Post Topic: AXP322 power on/off & config/maint mode
    Posted: 10 Sep 2020 at 10:39am
With the AXP322 being remote, there doesn't seem to be any power on/off possibility since the AXP340 MODE button is missing. The only AXP322 operational info that I've found is in the IFD PG. There is no AXP322 PG.

Is there any way to do this from the panel, other than pulling and resetting the circuit breaker?

Also, how does one get the AXP322 into configuration mode to enter the various setup options? I suppose this is found in the installation manual which is only available to avionics reps? How can one retrieve the aircraft code that is configured without going through said avionics reps (==>$$$$$)?


Vince
Back to Top
oskrypuch View Drop Down
Senior Member
Senior Member


Joined: 09 Nov 2012
Location: CYFD
Status: Offline
Points: 3061
Post Options Post Options   Thanks (0) Thanks(0)   Quote oskrypuch Quote  Post ReplyReply Direct Link To This Post Posted: 10 Sep 2020 at 1:39pm
The AXP322 settings are controlled directly from the IFD, on a dedicated maintenance page together with some added settings on the user setup page, both accessible by the end user.

I have never had a need to power cycle the 322, but I do have a breaker I could use.

Other than setting the code (with the keyboard) and IDENTing (with a switch on the yoke), I never do anything with the mode or other functions, it switches appropriately and automatically from GND to ACTIVE mode. On the ground, in GND mode, it will respond to ASDE-X ground radar.

* Orest


Edited by oskrypuch - 10 Sep 2020 at 1:45pm
Back to Top
chflyer View Drop Down
Senior Member
Senior Member
Avatar

Joined: 24 Jan 2013
Location: LSZK
Status: Offline
Points: 1035
Post Options Post Options   Thanks (0) Thanks(0)   Quote chflyer Quote  Post ReplyReply Direct Link To This Post Posted: 10 Sep 2020 at 2:40pm
Thanks for the info Orest. That clarifies everything.
Vince
Back to Top
oskrypuch View Drop Down
Senior Member
Senior Member


Joined: 09 Nov 2012
Location: CYFD
Status: Offline
Points: 3061
Post Options Post Options   Thanks (0) Thanks(0)   Quote oskrypuch Quote  Post ReplyReply Direct Link To This Post Posted: 10 Sep 2020 at 9:09pm
đź‘Ť
Back to Top
LeeMajors View Drop Down
Newbie
Newbie


Joined: 15 Jun 2021
Location: BNA
Status: Offline
Points: 29
Post Options Post Options   Thanks (0) Thanks(0)   Quote LeeMajors Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2021 at 9:55pm
I have a similar question.  

The plane I bought had a 540 put in it after a 550 was installed.  The SkyTrax322 stopped sending the Aircraft identification to ADS-B and the FAA grounded us from rule airspace until rectified.

We went into the maintenance menu on the IFD540 and put the tail number back in but it’s still not transmitting the data to ADS-B.

Does anyone have an install manual for this or at least that section of programming?  It’s annoying to have to find a dealer, work it in, and pay hundreds of dollars for something I can probably do in about 30 minutes if I had the manual.

Thanks,
Back to Top
AviSteve View Drop Down
Admin Group
Admin Group
Avatar

Joined: 12 Feb 2018
Location: Melbourne, FL
Status: Offline
Points: 2244
Post Options Post Options   Thanks (0) Thanks(0)   Quote AviSteve Quote  Post ReplyReply Direct Link To This Post Posted: 18 Jun 2021 at 9:56am
Originally posted by LeeMajors LeeMajors wrote:

I have a similar question.  

The plane I bought had a 540 put in it after a 550 was installed.  The SkyTrax322 stopped sending the Aircraft identification to ADS-B and the FAA grounded us from rule airspace until rectified.

We went into the maintenance menu on the IFD540 and put the tail number back in but it’s still not transmitting the data to ADS-B.

Does anyone have an install manual for this or at least that section of programming?  It’s annoying to have to find a dealer, work it in, and pay hundreds of dollars for something I can probably do in about 30 minutes if I had the manual.

Thanks,
Check Flight ID on the setup page.  Is it set to your tail number?
Steve Lindsley
Avidyne Engineering
Back to Top
AndyMeyer View Drop Down
Newbie
Newbie


Joined: 05 Oct 2019
Location: SE PA
Status: Offline
Points: 29
Post Options Post Options   Thanks (0) Thanks(0)   Quote AndyMeyer Quote  Post ReplyReply Direct Link To This Post Posted: 03 Jun 2023 at 9:55am
On the latest software, it seems that there are two places where you need to put our Flight ID info...
One is in the Mx mode where you enter your HEX ID code, and one in the user setup page where you set your Flight ID. 
This bit me after my latest SW update. 

The HEX ID code must be entered in the MX pages; The flight ID code is used if you're doing something like a Veterans Airlift Command flight where you're not flying under your normal N number, but something like Hero340, etc... Nice feature add! Set the flight ID to your normal callsign for normal ops...

Andy
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.01
Copyright ©2001-2018 Web Wiz Ltd.

This page was generated in 0.107 seconds.