![]() |
IFD540 & Stec-55x Glideslope Wiring |
Post Reply ![]() |
Author | |
jonesronc ![]() Newbie ![]() Joined: 31 May 2016 Status: Offline Points: 20 |
![]() ![]() ![]() ![]() ![]() Posted: 21 Aug 2016 at 5:31pm |
I have the above with an NSD-360A HSI installed in April; GS arms but won't couple. HSI GS indications normal. ILS & GPS with vertical guidance both don't couple. I thought at first I just didn't have the parameters just right, but after more than a dozen precision approaches I've definitely got the flying part down. It looks like the 540 has 3 GS output wires and the Stec wants 4. Has anybody had this problem or know of a likely fix? Thx.
|
|
![]() |
|
rolfe_tessem ![]() Senior Member ![]() ![]() Joined: 06 Jan 2012 Location: Massachusetts Status: Offline Points: 188 |
![]() ![]() ![]() ![]() ![]() |
I had a 55x installed on my Bonanza with a 540 a few months ago by Stellar Avionics in Chester, CT. You might want to give them a call. I have a King HSI, although I can't imagine why that would make a difference. Mine works flawlessly after one initial glitch was fixed.
Edited by rolfe_tessem - 21 Aug 2016 at 10:40pm |
|
![]() |
|
wookie ![]() Groupie ![]() Joined: 18 Feb 2015 Location: Colorado Status: Offline Points: 56 |
![]() ![]() ![]() ![]() ![]() |
Does your 55x have autotrim? BH
|
|
BH
|
|
![]() |
|
rolfe_tessem ![]() Senior Member ![]() ![]() Joined: 06 Jan 2012 Location: Massachusetts Status: Offline Points: 188 |
![]() ![]() ![]() ![]() ![]() |
Yes it does and it works perfectly! Rolfe
|
|
![]() |
|
wookie ![]() Groupie ![]() Joined: 18 Feb 2015 Location: Colorado Status: Offline Points: 56 |
![]() ![]() ![]() ![]() ![]() |
Reason I ask is that there are some installations where auto trim is required
for GS coupling. Not an issue here, it's something else. BH |
|
BH
|
|
![]() |
|
jonesronc ![]() Newbie ![]() Joined: 31 May 2016 Status: Offline Points: 20 |
![]() ![]() ![]() ![]() ![]() |
My current aircraft doesn't have autotrim, but neither did my previous twin with a -30, and it coupled fine. Al at Avidyne tech support said go from GAMA 429 to GAMA 429 with Graphics/INT on the ARINC config page, but the aircraft couldn't hardly keep course with that. S-Tec said go with the plain ARINC 429 format. Which format are y'all using? Ron |
|
![]() |
|
rolfe_tessem ![]() Senior Member ![]() ![]() Joined: 06 Jan 2012 Location: Massachusetts Status: Offline Points: 188 |
![]() ![]() ![]() ![]() ![]() |
I'm sure my avionics shop knows, but I haven't a clue. I'm due in there shortly for a Sandia Quattro and will ask... Rolfe |
|
![]() |
|
wookie ![]() Groupie ![]() Joined: 18 Feb 2015 Location: Colorado Status: Offline Points: 56 |
![]() ![]() ![]() ![]() ![]() |
All the 429 affects is GPS steering.
The '30 only supports altitude hold as a vertical mode.... it does not have GS coupling FWIW. BH |
|
BH
|
|
![]() |
|
jonesronc ![]() Newbie ![]() Joined: 31 May 2016 Status: Offline Points: 20 |
![]() ![]() ![]() ![]() ![]() |
Regarding -30, come to think of it, you're right - I would set trim for Ground Speed/2 *100 = fpm and down I'd go; I was confusing that with a TruTrak I was flying at the time. Regarding ARINC, why did Avidyne think it was an ARINC issue when I called them? Ron |
|
![]() |
|
wookie ![]() Groupie ![]() Joined: 18 Feb 2015 Location: Colorado Status: Offline Points: 56 |
![]() ![]() ![]() ![]() ![]() |
If the 429 isn't connecting, the symptom would be that the gpss would just wander around. There are several flavors and speeds on 429 -- I'm not conversant, sorry. bh
|
|
BH
|
|
![]() |
|
jonesronc ![]() Newbie ![]() Joined: 31 May 2016 Status: Offline Points: 20 |
![]() ![]() ![]() ![]() ![]() |
Fixed the problem; one of the high density pins on P1001 had lost its lock and was pushing in when the radio was loaded into its tray. Reset the pin and all works now. yay
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |