IFD540 AND GTX345
Printed From: Avidyne
Category: Avidyne General
Forum Name: IFD 5 Series & IFD 4 Series Touch Screen GPS/NAV/COM
Forum Description: Topics on Avidyne's IFD 5 Series and IFD 4 Series Touch Screen GPS/NAV/COM
URL: http://forums.avidyne.com/forum_posts.asp?TID=1631
Printed Date: 14 Nov 2024 at 1:45am
Software Version: Web Wiz Forums 12.01 - http://www.webwizforums.com
Topic: IFD540 AND GTX345
Posted By: jwalton49
Subject: IFD540 AND GTX345
Date Posted: 30 Oct 2018 at 3:15pm
| Can someone tell me where Avidyne specifies the 429 data protocol between the GTX345 and the 540? |
Replies:
Posted By: LANCE
Date Posted: 30 Oct 2018 at 8:02pm
The Avidyne Service letter 606-00182-015 of 3/29/2017
  |
jwalton49 wrote:Posted By: Cruiser
Date Posted: 30 Oct 2018 at 8:03pm
| not sure what you are looking for but the configuration settings are in the install manual. |
Posted By: Melohn
Date Posted: 31 Oct 2018 at 5:52pm
|
How does this work if there is an EX5000 MFD in the setup? The 345 needs to talk to it using the same rs422 output port, but with a different format. |
Posted By: Cruiser
Date Posted: 01 Nov 2018 at 5:31pm
| can't do it. You need to choose. |
Posted By: matthewsjl
Date Posted: 09 Jul 2019 at 11:55am
|
Now I've been approved for posting, what is the purpose of the RS-232 line going from the GTX-345 pin 8 to the IFD pin 57? Thanks, John.
|
Posted By: jwalton49
Date Posted: 09 Jul 2019 at 12:00pm
| Mine is wired like that but both ports are turned off so I guess nothing. |
Posted By: matthewsjl
Date Posted: 09 Jul 2019 at 12:08pm
|
Well, the line from the IFD to the 345 should be for GPS position source for ADS-B. I too have turned off the 345->IFD and haven't noticed anything yet not working but it's also waiting to be flown after the install. John |
Posted By: matthewsjl
Date Posted: 16 Jul 2019 at 10:23am
|
So, just to bring this full circle after speaking to Avidyne Tech Support. For 10.2.3.1, the Installation manual has been updated to cover the GTX-345. Below is the wiring:  The settings are indicated as follows:  That should clean all this up. John
|
Posted By: matthewsjl
Date Posted: 20 Sep 2019 at 11:46pm
|
Question..... If you don't have the AIRINC line between the GTX-345 and the IFD, does the RS-422 line carry wx and traffic from the GTX-345? If using the setting "Capstone HS Wx+Trfc" would I get both wx and traffic on the display? Is there any difference in the data stream between the AIRINC and RS-422? John PS: My reading seems to indicate that the GTX-345 RS-422 stream when set to "OPT LGCY ADSB" is the GDL-90 protocol...... but there is little information on this.
|
Posted By: matthewsjl
Date Posted: 23 Sep 2019 at 10:36am
|
OK - so I tried to set "Capstone HS Wx+Traffic" as the receive protocol on the IFD and now have both displayed via the RS-232 line. No 429 line required. John
|
Posted By: Cruiser
Date Posted: 23 Sep 2019 at 4:28pm
|
I get traffic over the ARINC 429 line from the GTX 345 In a one hour flight I get the TIS-B with the red circle and slash through it more than I get the traffic It clears itself for a while but then fails again. Anyone know why ?
|
Posted By: forkauto
Date Posted: 23 Sep 2019 at 4:54pm
| Could be that you are not picking up a station, If you are in the middle of nowhere, sometimes mine will go out or say degraded. |