![]() |
Typos |
Post Reply ![]() |
Author | |
oskrypuch ![]() Senior Member ![]() Joined: 09 Nov 2012 Location: CYFD Status: Offline Points: 3059 |
![]() ![]() ![]() ![]() ![]() Posted: 18 Nov 2014 at 2:15pm |
Just starting this thread for typos I find, here is the first. No need to acknowledge.
PG p4-36 - ARINC420 * Orest |
|
![]() |
|
oskrypuch ![]() Senior Member ![]() Joined: 09 Nov 2012 Location: CYFD Status: Offline Points: 3059 |
![]() ![]() ![]() ![]() ![]() |
PG p5-8 - In OBS TO (defined as the when the difference ...
Suggest: In OBS TO (when the difference ... PG p5-9 - In OBS FROM (defined as the difference .... Suggest: In OBS FROM (when the difference .... * Orest Edited by oskrypuch - 18 Nov 2014 at 6:25pm |
|
![]() |
|
oskrypuch ![]() Senior Member ![]() Joined: 09 Nov 2012 Location: CYFD Status: Offline Points: 3059 |
![]() ![]() ![]() ![]() ![]() |
PG p5-17 - ... transitioning to 350 feet either side at the runway threshold (slightly looser than a localizer)
Actually, a localizer is always setup to be exactly 700ft wide at the runway threshold, 350ft to either side. Suggest: ... transitioning to 350 feet either side at the runway threshold (the same as a localizer) * Orest Edited by oskrypuch - 18 Nov 2014 at 9:55pm |
|
![]() |
|
Royski ![]() Groupie ![]() ![]() Joined: 26 Feb 2013 Status: Offline Points: 87 |
![]() ![]() ![]() ![]() ![]() |
I might have found a typo in the installation manual as I troubleshoot a communication issue with my Shadin Miniflo fuel computer.
The Avidyne manual refers to a "Shadin 91204XM," which is not a model that appears in The Google. [EDIT or perhaps this typo originated with G***** ] The Miniflo is a 91204XT-D and the Microflo is 91204XT-38-D. Can I assume that 9204XM in the installation manual is intended to be 91204XT? Edited by Royski - 18 Dec 2014 at 10:12am |
|
![]() |
|
AviJake ![]() Admin Group ![]() Joined: 26 Mar 2009 Location: Lincoln MA Status: Offline Points: 2815 |
![]() ![]() ![]() ![]() ![]() |
Yes, those Shadin fuel flow computers have a typo. They are correct in the installation drawings in the back of the book but the data listed in Section 2.3 Interfaces and in Section 7.5.3 RS-232 Port Configurations are wrong and will be corrected in the Install Manual that comes out with Rel 10.0.3.0.
The Shadin fuel flow's that are supported include: 91204XT(38)D Miniflo-L 91204XT-D Miniflo-L 91053XP Digiflo-L 91053XT-D Digiflo-L 91802-() DigiData |
|
Steve Jacobson
sjacobson@avidyne.com |
|
![]() |
|
sikhpilotmd ![]() Groupie ![]() Joined: 08 Oct 2014 Location: KISP Status: Offline Points: 69 |
![]() ![]() ![]() ![]() ![]() |
My 540 s are not getting any input from the miniflo. The installer says all the wiring is good. Any suggestions?
|
|
![]() |
|
ddgates ![]() Senior Member ![]() ![]() Joined: 12 Aug 2011 Location: Deer Valley Status: Offline Points: 1100 |
![]() ![]() ![]() ![]() ![]() |
I've had the same thing since install.
|
|
David Gates
|
|
![]() |
|
AviJake ![]() Admin Group ![]() Joined: 26 Mar 2009 Location: Lincoln MA Status: Offline Points: 2815 |
![]() ![]() ![]() ![]() ![]() |
Work fine in our lab and airplanes. Can you send your exact setup page configuration from Mx Mode? It's the RS-232 configuration page I care about and is the 2nd one in Mx Mode Configuration tab. You can also send the logs if that's easier since we can extract the setup from there.
|
|
Steve Jacobson
sjacobson@avidyne.com |
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |