Release 10.2.3.1

I did my update myself, with my A&P oversite. Went fine, I'd say it took about 50 min. As far as I can tell no settings were lost. I really appreciate Avidyne making it available so I don't have to bring it in to a dealer!

When you select the Stratus on Wi-Fi in the iPad Settings, Is Avidyne showing up in "Devices" in Foreflight (it may take up to a minute to connect)?

Went back to the plane and found my mistake.  I had all the digits correct (using zero instead of letter O) but the one mistake I made was using a "capital" S in Stratus2S instead of Stratus2s as it appeared.  That one mistake made all the difference.  :).   Thank you. 

I would like a copy of the manual too. One part of the service bulletin says rev 15, but another says rev 17. I believe the latter is the correct one, right?

AviSteve wrote: Use the same link that you used to get the software update.  We have posted an updated Service Bulletin (correcting the wrong rev reference), the Install Manual, and Instructions for Continued Airworthiness.

Did the update on my IFD 440 this morning along with my SC and everything completed with no errors but now getting an "ADS-B GPS Position Invalid: ADS-B Traffic Sensor lacks GPS position" error on my IFD.  It's connected to a FreeFlight RANGR and everything worked before the IFD upgrade.  The input/output configs on the IFD match what they were before the upgrade.  Any thoughts on what to check?

My problem now is I cannot get the IDE 100 to work in remote mode (worked fine in last revision) I turn on the Stratus box, select Strutus2XXXXX from Ipad mini with foreflight, Type Stratus2XXXXX into the second block on maint mode then select remote.

Then select Stratus2XXXX Remote from user side and finally, Select Stratus2xxxxx from the WIFI section on the IDE 100 App.

Am I correct so far?

When I do this, the Foreflight Mini and the IDF Mini seem to log on but the IDF 100 fails to log on, ie no com or gps data comes across.

What am I doing wrong?

BTW, if logging on direct it logs right on (Local),

So I had my update to the latest software (IFD540), and had my old GDL69A activated for a month, but can’t seem to get the WX to show. Is there anyway to update the GDL FIRMWARE so that it will work with my 540? 

10.2.3.1 updated smoothly on both IFD 540 and IFD 440.  Less than an hour each once started, but a lot more in prep and post.  Some of the new Config pages are different than before (10.2.0.0.A).  My data blocks on the 540's right side had minor differences, and the top of the 440 were changed to the same as the 540.  

You should also include the SNs of the boxes updated.

donemory wrote: Since doing the 10.2.3.1 update, every time I power on my IFD540, (others say their IFD440 does the same), it displays the bottom end of my data blocks and I have to scroll back to the top. Has any one else had this issue and is there a way to correct it so that it displays the top end of the data blocks?  Avidyne any fix here?

Same issue here... 

Yes, agree the COM PRESET is now not working on the Bluetooth keyboard. 

Edited by DH82FLYER - 18 Jun 2019 at 11:07pm

Ralph wrote: Did anyone notice the COM PRESET not working from the blue tooth keyboard after the upgrade?  I also noted that I couldn't change NAV frequencies on the iPad.  Avidyne acknowledges the latter but I didn't get a solid answer on the blue tooth keyboard issue.  Everything else on the blue tooth appears to function normally.

Sorry, no it's in the IFD software, not just IFD100.

Since this software update, there appears to be a problem with the Fuel Range Rings.

The problem occurs if I zoom the map out to around 800 miles to check the Fuel Range Rings and then pan across and zoom in on the rings. 

They then suddenly disappear at a map range of 80 miles and below.

They reappear when I zoom back out. 

This issue occurs whether I zoom with either the knob or the touch screen. 

Has anyone else seen this behaviour?

Thomas

Edited by DH82FLYER - 22 Jun 2019 at 6:57pm

Sounds like a consensus.  We'll find it and fix it in the next release.

Here's a new one:

Reinforcing the Map/Data Blocks scrolling down on boot-up issue, even tho' Steve said  "Consensus; will fix in the next release..."  

That button is disabled when the IFD thinks the aircraft is airborne.

You had me wondering myself but I really thought I had entered configuration mode that way since the upgrade.  When I went flying tonight, I tried it on the ground before takeoff and it does behave as it did previously.   I also think I have done it in my hanger before also so I’m a little confused. Report back when you’ve tried again please

I saw this last week also. Scrolling through the alert the notification was for no airmets received for 120 minutes.

Re: 10.2.3.1

Thanks, Steve.